Select an Error Code or Type an Error Code to begin searching
| Error |
|---|
| Error |
|---|
These results are ranked by popularity.
| Error | |
|---|---|
| C5103 | Description: Transport motor turning at abnormal timing. The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| C1195 | Description: Paper discharge control motor malfunction (When FS-534SD is installed) The curl cover detection sensor (PS2) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed after the paper discharge control motor |
| CD705, CD706 | Description: • CD705: Mechanical controller sub-CPU flash ROM device error • CD706: Mechanical controller sub-CPU flash ROM error. • CD705: An erase error or other device fault occurs during mechanical controller sub-CPU flash ROM writing. • CD706: A dat |
| CC170 ... CC186 | Description: • CC170: Dynamic link error during starting (AP0) • CC171: Dynamic link error during starting (AP1) • CC172: Dynamic link error during starting (AP2) • CC173: Dynamic link error during starting (AP3) • CC174: Dynamic link error during starti |
| C0211 | Description: Manual feed up/down abnormality • Paper is not turned OFF (unblock) the bypass tray position sensor (PS28) even after the transport motor (M1) rotates for a given period of time after the position is switched from stand by position at lift-u |
The most common error codes.
| Error | |
|---|---|
| C5103 | Description: Transport motor turning at abnormal timing. The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| C1195 | Description: Paper discharge control motor malfunction (When FS-534SD is installed) The curl cover detection sensor (PS2) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed after the paper discharge control motor |
| CD705, CD706 | Description: • CD705: Mechanical controller sub-CPU flash ROM device error • CD706: Mechanical controller sub-CPU flash ROM error. • CD705: An erase error or other device fault occurs during mechanical controller sub-CPU flash ROM writing. • CD706: A dat |
| CC170 ... CC186 | Description: • CC170: Dynamic link error during starting (AP0) • CC171: Dynamic link error during starting (AP1) • CC172: Dynamic link error during starting (AP2) • CC173: Dynamic link error during starting (AP3) • CC174: Dynamic link error during starti |
| C0211 | Description: Manual feed up/down abnormality • Paper is not turned OFF (unblock) the bypass tray position sensor (PS28) even after the transport motor (M1) rotates for a given period of time after the position is switched from stand by position at lift-u |
| C5103 | Description: Transport motor turning at abnormal timing. The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. |
| C1195 | Description: Paper discharge control motor malfunction (When FS-534SD is installed) The curl cover detection sensor (PS2) is not turned ON (blocked) or OFF (unblocked) even after the set period of time has elapsed after the paper discharge control motor |
| CD705, CD706 | Description: • CD705: Mechanical controller sub-CPU flash ROM device error • CD706: Mechanical controller sub-CPU flash ROM error. • CD705: An erase error or other device fault occurs during mechanical controller sub-CPU flash ROM writing. • CD706: A dat |
| CC170 ... CC186 | Description: • CC170: Dynamic link error during starting (AP0) • CC171: Dynamic link error during starting (AP1) • CC172: Dynamic link error during starting (AP2) • CC173: Dynamic link error during starting (AP3) • CC174: Dynamic link error during starti |
| C0211 | Description: Manual feed up/down abnormality • Paper is not turned OFF (unblock) the bypass tray position sensor (PS28) even after the transport motor (M1) rotates for a given period of time after the position is switched from stand by position at lift-u |